思科BGP AS-PATH配置实验案例
我要评论本文实例讲述了思科BGP AS-PATH配置。分享给大家供大家参考，具体如下：
Cisco BGP AS-PATH配置实例如下图示：
R1:
interface Loopback0
ip address 1.1.1.1 255.255.255.255
interface FastEthernet0/0
ip address 12.1.1.1 255.255.255.0
interface FastEthernet0/1
ip address 14.1.1.1 255.255.255.0
router eigrp 1
network 1.1.1.1 0.0.0.0
network 12.1.1.0 0.0.0.255
network 14.1.1.0 0.0.0.255
no auto-summary
router bgp 100
bgp router-id 1.1.1.1
bgp log-neighbor-changes
no synchronization
neighbor 2.2.2.2 remote-as 100
neighbor 2.2.2.2 update-source Loopback0
neighbor 2.2.2.2 next-hop-self
neighbor 3.3.3.3 remote-as 100
neighbor 3.3.3.3 update-source Loopback0
neighbor 3.3.3.3 next-hop-self
neighbor 4.4.4.4 remote-as 200
neighbor 4.4.4.4 ebgp-multihop 255
neighbor 4.4.4.4 update-source Loopback0
neighbor 4.4.4.4 next-hop-self
no auto-summary
R2:
interface Loopback0
ip address 2.2.2.2 255.255.255.255
interface FastEthernet0/0
ip address 12.1.1.2 255.255.255.0
interface FastEthernet0/1
ip address 23.1.1.2 255.255.255.0
router eigrp 1
network 2.2.2.2 0.0.0.0
network 12.1.1.0 0.0.0.255
network 23.1.1.0 0.0.0.255
no auto-summary
router bgp 100
no synchronization
bgp router-id 2.2.2.2
bgp log-neighbor-changes
neighbor 1.1.1.1 remote-as 100
neighbor 1.1.1.1 update-source Loopback0
neighbor 1.1.1.1 next-hop-self
neighbor 3.3.3.3 remote-as 100
neighbor 3.3.3.3 update-source Loopback0
neighbor 3.3.3.3 next-hop-self
no auto-summary
R3:
interface Loopback0
ip address 3.3.3.3 255.255.255.255
interface FastEthernet0/0
ip address 34.1.1.3 255.255.255.0
interface FastEthernet0/1
ip address 23.1.1.3 255.255.255.0
router eigrp 1
network 3.3.3.3 0.0.0.0
network 23.1.1.0 0.0.0.255
network 34.1.1.0 0.0.0.255
no auto-summary
router bgp 100
no synchronization
bgp router-id 3.3.3.3
bgp log-neighbor-changes
neighbor 1.1.1.1 remote-as 100
neighbor 1.1.1.1 update-source Loopback0
neighbor 1.1.1.1 next-hop-self
neighbor 2.2.2.2 remote-as 100
neighbor 2.2.2.2 update-source Loopback0
neighbor 2.2.2.2 next-hop-self
neighbor 4.4.4.4 remote-as 200
neighbor 4.4.4.4 ebgp-multihop 255
neighbor 4.4.4.4 update-source Loopback0
neighbor 4.4.4.4 next-hop-self
no auto-summary
R4:
interface Loopback0
ip address 4.4.4.4 255.255.255.255
interface FastEthernet0/0
ip address 34.1.1.4 255.255.255.0
interface FastEthernet0/1
ip address 14.1.1.4 255.255.255.0
router eigrp 1
network 4.4.4.4 0.0.0.0
network 14.1.1.0 0.0.0.255
network 34.1.1.0 0.0.0.255
no auto-summary
ip prefix-list 1 seq 5 permit 4.4.4.4/32
route-map as_path permit 10
match ip address prefix-list 1
set as-path prepend 600 700
router bgp 200
no synchronization
bgp log-neighbor-changes
neighbor 1.1.1.1 remote-as 100
neighbor 1.1.1.1 ebgp-multihop 255
neighbor 1.1.1.1 update-source Loopback0
neighbor 1.1.1.1 next-hop-self
neighbor 3.3.3.3 remote-as 100
neighbor 3.3.3.3 ebgp-multihop 255
neighbor 3.3.3.3 update-source Loopback0
neighbor 3.3.3.3 next-hop-self
neighbor 3.3.3.3 route-map as_path out
no auto-summary
R4(config-router)#do ping 1.1.1.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 1.1.1.1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 32/36/40 ms
R4(config-router)#do traceroute 1.1.1.1Type escape sequence to abort.
Tracing the route to 1.1.1.11 34.1.1.3 8 msec 12 msec 24 msec
2 23.1.1.2 32 msec 36 msec 44 msec
3 12.1.1.1 32 msec 44 msec 32 msec
R4(config-router)#
R4(config-router)#do show ip route
Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2
i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
ia - IS-IS inter area, * - candidate default, U - per-user static route
o - ODR, P - periodic downloaded static routeGateway of last resort is not set
34.0.0.0/24 is subnetted, 1 subnets
C 34.1.1.0 is directly connected, FastEthernet0/0
1.0.0.0/32 is subnetted, 1 subnets
D 1.1.1.1 [90/460800] via 34.1.1.3, 00:05:23, FastEthernet0/0
2.0.0.0/32 is subnetted, 1 subnets
D 2.2.2.2 [90/435200] via 34.1.1.3, 00:03:07, FastEthernet0/0
3.0.0.0/32 is subnetted, 1 subnets
D 3.3.3.3 [90/409600] via 34.1.1.3, 00:05:25, FastEthernet0/0
4.0.0.0/32 is subnetted, 1 subnets
C 4.4.4.4 is directly connected, Loopback0
23.0.0.0/24 is subnetted, 1 subnets
D 23.1.1.0 [90/307200] via 34.1.1.3, 00:05:36, FastEthernet0/0
12.0.0.0/24 is subnetted, 1 subnets
D 12.1.1.0 [90/332800] via 34.1.1.3, 00:03:10, FastEthernet0/0
14.0.0.0/24 is subnetted, 1 subnets
D 14.1.1.0 [90/358400] via 34.1.1.3, 00:05:37, FastEthernet0/0
相关文章
- 这篇文章主要介绍了思科Cisco BGP常用show命令,总结整理了思科Cisco BGP使用show命令查看BGP路由表与网络状态相关操作技巧,需要的朋友可以参考下2020-04-05
- 这篇文章主要介绍了BGP边界网关路由协议学习笔记之属性和选路规则,详细分析了BGP属性、路由条件及相关配置命令使用技巧,需要的朋友可以参考下2020-04-08
- 这篇文章主要介绍了BGP边界网关路由协议路由聚合操作,汇总整理了BGP边界网关路由协议路由聚合相关概念、原理、操作命令与使用注意事项,需要的朋友可以参考下2020-04-07
- 这篇文章主要介绍了BGP边界网关路由协议,总结整理了BGP边界网关路由协议的相关概念、原理、配置命令及操作注意事项,需要的朋友可以参考下2020-04-07
最常用路由协议RIP-1/2 OSPF IS-IS BGP的特点对比
RIP协议是最早的路由协议，OSPF是目前应用最广泛的IGP协议，IS-IS是另外一种链路状态型的路由协议，BGP协议是唯一的EGP协议，那么这几种路由协议有什么特点和不同呢?下面就2017-04-06
在bgp同步打开的情况下,一个BGP路由器不会把那些通过ibgp邻居学到的bgp路由通告给自己的ebgp邻居;除非自己的igb路由表中存在这些路由,才可以向ebgp路由器通告；有需要的朋2016-10-16
路由包括两个基本的动作：确定最佳路径和信息群（通常称为分组）通过网络的传输。通过网络传输分组相对较简单， 而路径的确定可以分复杂。 BGP 就是当今网络中实现路径选择2016-10-16
BGP作为一种广泛使用的边界网关路由协议，从设计上提供了强大的路由过滤能力，与一般的访问列表ACL不同的是，基于BGP属性的路由过滤是通过对路由属性的控制或修改来完成的2016-10-16- 这篇文章主要为大家介绍了边界网关协议BGP的概念，怎么配置BGP？下面文章里有详细的BGP基本配置的方法步骤，有兴趣的可以和脚本之家的小编一起来看一下2014-09-24
- BGP协议是运行在TCP之上的，所以TCP的参数设置会影响BGP的性能。在路由数目比较少的情况下TCP的参数调整可能对BGP性能影响不大，但是当路由数目比较巨大的时候调整TCP参数2012-11-19
最新评论