关于LAN网内VLAN与Trunk的详细配置
发布时间:2010-09-07 23:39:33 作者:佚名 我要评论
此实验过程是在Boson NetSim for CCNP version 6.0 BETA 1软件下做的。其中使用2台C2905switch和4台PC机。
实验内容:
1、 配置控制端口和虚拟线路
2、设置VLAN两个,分别为:VLAN100 Pcontrol和VLAN200 Accout
3、分别将接口加入到VLA
此实验过程是在Boson NetSim for CCNP version 6.0 BETA 1软件下做的。其中使用2台C2905switch和4台PC机。
实验内容:
1、 配置控制端口和虚拟线路
2、设置VLAN两个,分别为:VLAN100 Pcontrol和VLAN200 Accout
3、分别将接口加入到VLAN100和VLAN200后配置Trunk线路,保证VLAN间的通信
4、最后进行测试是否成功
关于LAN网内VLAN与Trunk的详细配置
SW1(C2950)交换机测试详细步骤及结果:
CLI session with the switch is open.
To end the CLI session, enter [Exit].
Switch>
%LINK-3-UPDOWN: Interface FastEthernet0/1, changed state to down
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to down
%LINK-3-UPDOWN: Interface FastEthernet0/4, changed state to down
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/4, changed state to down
%LINK-3-UPDOWN: Interface FastEthernet0/5, changed state to down
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/5, changed state to down
%LINK-3-UPDOWN: Interface FastEthernet0/6, changed state to down
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/6, changed state to down
%LINK-3-UPDOWN: Interface FastEthernet0/7, changed state to down
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/7, changed state to down
%LINK-3-UPDOWN: Interface FastEthernet0/8, changed state to down
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/8, changed state to down
%LINK-3-UPDOWN: Interface FastEthernet0/9, changed state to down
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/9, changed state to down
%LINK-3-UPDOWN: Interface FastEthernet0/11, changed state to down
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/11, changed state to down
%LINK-3-UPDOWN: Interface FastEthernet0/12, changed state to down
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/12, changed state to down
Switch>enable
Switch#show version
Boson Operating Simulation Software
BOSS (tm) C2900 Software (C2900-Enterprise), Version 12.1, RELEASE SOFTWARE
Copyright (c) 1998-2003 by Boson Software, Inc.
BOSS ROM: System Bootstrap, Version 12.2, RELEASE SOFTWARE
Switch Uptime Is 0 days, 0 hours, 0 minutes
System restarted by power-on
System image file is ""flash:c2900-enterprise.12.1.boss"", booted via flash
Boson 2900 (BOSS) processor (revision 5.0)
12 FastEthernet/IEEE 802.3 interface(s)
32K bytes of simulated non-volatile configuration memory.
8192K bytes of simulated System flash (Read/Write)
Switch#
Switch#
Switch#show runn
!
Version 12.1
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname Switch
!
!
!
ip subnet-zero
spanning-tree extend system-id
!
!
!
!
!
!
!
!
interface FastEthernet0/1
!
interface FastEthernet0/2
!
Switch#show runn
!
Version 12.1
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname Switch
!
!
!
ip subnet-zero
spanning-tree extend system-id
!
!
!
!
!
!
!
!
interface FastEthernet0/1
!
interface FastEthernet0/2
!
interface FastEthernet0/3
!
interface FastEthernet0/4
!
interface FastEthernet0/5
!
interface FastEthernet0/6
!
interface FastEthernet0/7
!
interface FastEthernet0/8
!
interface FastEthernet0/9
!
interface FastEthernet0/10
!
interface FastEthernet0/11
!
interface FastEthernet0/12
!
vtp domain bigdomain
!
interface Vlan 1
no ip address
no ip route-cache
!
!
ip classless
no ip http server
!
!
!
!
line con 0
transport input none
line aux 0
line vty 0 15
!
no scheduler allocate
end
Switch#
Switch#
Switch#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)#hostname SW1
SW1(config)#line console 0
SW1(config-line)#exec-timeout 20 0
SW1(config-line)#logging synchronous
SW1(config-line)#password dsfeng
SW1(config-line)#login
SW1(config-line)#line vty 0 15
SW1(config-line)#exec-timeout 15 0
SW1(config-line)#logging synchronous
SW1(config-line)#password dsfeng
SW1(config-line)#login
SW1(config-line)#enable secret cisco
SW1(config)#exit
SW1#
SW1#
SW1#vlan database
SW1(vlan)#vlan 100 name Pcontrol
VLAN 100 added:
Name:Pcontrol
SW1(vlan)#vlan 200 name Accout
VLAN 200 added:
Name:Accout
SW1(vlan)#exit
APPLY completed.
Exiting....
SW1#
SW1#
SW1#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
SW1(config)#interface fastethernet 0/2
SW1(config-if)#switchport mode access
SW1(config-if)#switchport access vlan 100
SW1(config-if)#exit
SW1(config)#interface fastethernet 0/3
SW1(config-if)#switchport mode access
SW1(config-if)#switchport access vlan 200
SW1(config-if)#exit
SW1(config)#interface fasteterhent 0/10
SW1(config-if)#switchport mode trunk
SW1(config-if)#switchport trunk encapsulation dot1q
SW1(config-if)#end
SW1#
SW1#
SW1#show interface fastethernet 0/2
FastEthernet0/2 is up, line protocol is up
Hardware is Fast Ethernet, address is 000C .6542.9093 (bia 000C .6542.9093)
MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Auto-duplex, Auto-speed
Encapsulation ARPA, loopback not set
ARP type: ARPA, ARP Timeout 04:00:00
Last input 02:29:44, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue :0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
269 packets input, 71059 bytes, 0 no buffer
Received 6 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
7290 packets output, 429075 bytes, 0 underruns
0 output errors, 3 interface resets
0 output buffer failures, 0 output buffers swapped out
SW1#
SW1#
SW1#show interface fastethernet 0/3
FastEthernet0/3 is up, line protocol is up
Hardware is Fast Ethernet, address is 000C .3849.2796 (bia 000C .3849.2796)
MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Auto-duplex, Auto-speed
Encapsulation ARPA, loopback not set
ARP type: ARPA, ARP Timeout 04:00:00
Last input 02:29:44, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue :0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
269 packets input, 71059 bytes, 0 no buffer
Received 6 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
7290 packets output, 429075 bytes, 0 underruns
0 output errors, 3 interface resets
0 output buffer failures, 0 output buffers swapped out
SW1#
SW1#
SW1#show interface fastethernet 0/10
FastEthernet0/10 is up, line protocol is up
Hardware is Fast Ethernet, address is 000C .3878.9745 (bia 000C .3878.9745)
MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Auto-duplex, Auto-speed
Encapsulation ARPA, loopback not set
ARP type: ARPA, ARP Timeout 04:00:00
Last input 02:29:44, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue :0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
269 packets input, 71059 bytes, 0 no buffer
Received 6 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
7290 packets output, 429075 bytes, 0 underruns
0 output errors, 3 interface resets
0 output buffer failures, 0 output buffers swapped out
SW1#
SW1#
SW1#show vlan
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active Fa0/1, Fa0/4, Fa0/5, Fa0/6
Fa0/7, Fa0/8, Fa0/9, Fa0/10
Fa0/11, Fa0/12
100 Pcontrol active Fa0/2
200 Accout active Fa0/3
1002 fddi-default active
1003 token-ring-default active
1004 fddinet-default active
1005 trnet-default active
VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2
---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------
1 enet 100001 1500 - - - - - 0 0
100 enet 100100 1500 - - - - - 0 0
200 enet 100200 1500 - - - - - 0 0
1002 fddi 101002 1500 - - - - - 0 0
1003 tr 101003 1500 - - - - - 0 0
1004 fdnet 101004 1500 - - - ieee - 0 0
1005 trnet 101005 1500 - - - ibm - 0 0
SW1#
SW1#
SW1#show cdp neighbors
Capability Codes: R - Router, T - Trans Bridge , B - Source Route Bridge
S -Switch, H - Host, i - IGMP, r - Repeater
Device ID Local Intrfce Holdtme Capability Platform Port ID
SW2 Fas0/10 167 T S 2950 Fas 0/10
SW1#
SW1#
SW1#show mac-address-table
Capability Codes: R - Router, T - Trans Bridge , B - Source Route Bridge
S -Switch, H - Host, i - IGMP, r - Repeater
Device ID Local Intrfce Holdtme Capability Platform Port ID
SW2 Fas0/10 167 T S 2950 Fas 0/10
Mac Address Table
------------------------------------------
Vlan Mac Address Type Ports
---- ----------- ---- -----
200 000C .9631.1997 DYNAMIC Fa0/3
100 000C .7036.8702 DYNAMIC Fa0/2
1 000C .3817.8412 DYNAMIC Fa0/10
1 000C .9623.5011 DYNAMIC Fa0/10
1 000C .1738.3819 DYNAMIC Fa0/10
Total Mac Addresses for this criterion: 5
SW1#
SW1#
SW1#show run
!
Version 12.1
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname SW1
enable secret 5 $sdf$6978yhg$jnb76sd
!
!
!
ip subnet-zero
spanning-tree extend system-id
!
!
!
!
!
!
!
!
interface FastEthernet0/1
!
interface FastEthernet0/2
switchport mode access
switchport access vlan 100
!
interface FastEthernet0/3
switchport mode access
switchport access vlan 200
!
interface FastEthernet0/4
!
interface FastEthernet0/5
!
interface FastEthernet0/6
!
interface FastEthernet0/7
!
interface FastEthernet0/8
!
interface FastEthernet0/9
!
interface FastEthernet0/10
switchport mode trunk
switchport trunk encapsulation dot1q
!
interface FastEthernet0/11
!
interface FastEthernet0/12
!
vtp domain bigdomain
!
interface Vlan 1
no ip address
no ip route-cache
!
vlan 100 name Pcontrol
vlan 200 name Accout
!
ip classless
no ip http server
!
!
!
!
line con 0
login
transport input none
password dsfeng
exec-timeout 15 0
logging synchronous
line aux 0
line vty 0 15
login
password dsfeng
!
no scheduler allocate
end
SW1#
SW1#
SW1#copy running-config startup-config
Destination filename [startup-config]?
Building configuration...
[OK]
SW1#
SW1#
相关文章
QQ邮箱文件怎么发送微信? 电脑qq邮箱中转站中文件分享到微信的方法
在使用邮箱软件的时候,有的用户想要通过QQ邮箱文件,QQ邮箱中存在这种功能,但是很多小伙伴不知道到底要如何操作,下面小编就给大家带来QQ邮箱文件发送微信教程,感兴趣的2024-09-29微信电脑版怎么独立窗口中打开订阅号? 订阅号独立窗口显示的教程
微信电脑版看订阅号的时候,想要独立窗口显示订阅号,该怎么操作呢?下面我们就来看看详细的教程2024-09-29Outlook在windows系统中有哪些快捷键? Outlook的键盘快捷方式大全
Outlook可以用它来收发电子邮件、管理联系人信息、记日记、安排日程、分配任务,新版Outlook for Windows带来了许多新功能,今天我们就来看看Outlook快捷键汇总2024-09-13微信怎么调默认浏览器? 微信设置默认浏览器打开网页链接的教程
微信怎么调默认浏览器?只需简单设置,在微信就可以使用默认浏览器打开网站,该怎么设置呢?详细请看下文介绍2024-08-14GameViewer怎么删除设备 GameViewer删除设备的步骤
GameViewer怎么删除设备?GameViewer 是一款专为游戏玩家设计的远程控制助手,下文中为大家带来了GameViewer删除设备步骤,需要的朋友快来看看吧2024-06-17- KOOK开黑啦游戏卡顿画面掉帧如何解决?kook语音是专为游戏用户研发的一款在线语音交流软件,它能够帮助用户在打游戏的过程中与队友保持一个在线沟通的状态,下文中为大家带2024-06-13
- RayLink如何进行文件传输?远程控制软件是一种常见的工具,可以方便地在不同设备之间传输文件,在本文中将介绍如何使用远程控制软件来实现文件传输,需要的朋友快来看看吧2024-06-12
- RayLink无人值守怎么实现?RayLink 是一款专为视觉行业打造的高清、流畅远程控制软件,它支持跨平台操作,无论是Windows、Mac、Linux还是移动设备,都能轻松实现远程控制和2024-06-12
RayLink如何添加或删除设备 Raylink详细使用教程
RayLink如何添加或删除设备?RayLink是一款功能强大的远程控制管理软件,支持跨平台连接,让用户能够轻松控制电脑、手机等设备,下文中为大家带来了RayLink添加或删除设备的2024-06-12- RayLink如何用设备码发起远程协助?RayLink是一款专为视觉行业设计的高清、流畅远程控制软件,支持跨平台操作,下文中为大家带来了设备码发起远程协助的方法,需要的朋友快2024-06-12
最新评论